How to Replace the Replacement Key Battery For the Saab 9-3
Saab owners have to follow a series of specific steps to add an additional ignition key. This requires the use of a handheld computer, known as Tech-2 which is to be used by the dealer. Then the transponder must be replaced and a key are required to be purchased.
Make sure to rotate your keys in order to prevent one from wearing out quicker than another. This will also keep your keys in pristine condition.
Replacement Case
The new key fobs do not look like the older Saab keys. They are equipped with electronics which make it hard to copy. This has made stealing cars significantly more difficult than 20 years ago. It also makes it more expensive to replace keys lost.
Saab 9-3 owners should have two keys that work. If one gets lost, it costs a lot of money to purchase a new one for the car since it requires replacing the CIM module and programming the locking cylinders. Dealers usually charge between $100-$200 for this.
There are several ways to get around these expensive. Some parts providers will search for the code from a spare key (usually the same one that opens the doors and turns the ignition) and cut a brand new key blade from metal for a fraction of the dealer's cost. The key must be exactly the same as the original for it to work in your vehicle.
You can also change the case yourself by following these steps. You'll need an flathead screwdriver and patience. With the screwdriver, you can pry apart the plastic, and then take off the emergency key. Once the case has been opened take the electronics out and place them into your new case. Place the key with the correct badge into the case.
Replacement Battery
The replacement battery for the Saab 9-3 is a cheap part that can be replaced quickly and easily. This YouTube DIY video Cyclone Cyd will show you how to replace the remote key fob battery in only four steps. This tutorial will work with any modern Saab key fob. However, the procedure might differ slightly.
The button is normally located close to the Saab logo on the back of the fob. This is usually located just below the Saab logo on the back of the fob. Then, use a flathead screwdriver into the small hole in this button. This will be enough to allow you to open the case of the fob so that you can replace the battery.
After you have installed the new CR1632 batteries, you can reassemble the remote key fob. Then, you can program it into your car. The procedure should take no more than an hour at most. It's a simple process that does not require any special tools.
The process can be a bit more complicated in the event that you lose your key, but it is possible. The dealer has to verify the VIN of the car, and then order a replacement key blade and TWICE module with the proper unique code. The dealer will then have to program the key using MDI, a new software tool.
Replacement Key Fob
The key fob is a device that locks and unlocks your car, it's got a battery within. The batteries last for a certain time and will eventually fail. This is a frequent issue in all vehicles. The good news is you can replace the battery in most key fobs, and not have to replace the entire case. Amazon sells replacement fobs that already have all the electronics installed. It is easy to remove the case and replace the batteries. You will need to remove the emergency key before you replace the batteries. To accomplish this, simply insert the screwdriver of a small flat head into the slot in the middle of the. The case will split once you move the screwdriver around it.
If you're ready to change your keys, have a spare in your possession. This will save you lots of money. If you have an additional key, ask the dealer to cut it and program it to your vehicle. This is much cheaper than purchasing a brand new key fob.
If you don't have a spare one, you can add an additional key to your car, however it requires a lot of research and effort. It will cost you a few hundred dollars to get an additional car key. The computer of the vehicle also has to be programmed. saab 93 key G28 Car Keys can be accomplished by a professional, but it is an expensive option for most owners.
Replacement Ignition
The current SAAB 9-3 features an alarm system that is more sophisticated that is based on a key code. If you lose your only key, it can be costly to replace it with another one since the car needs to include a computer and be programmed to accept a new key. Even a dealer can charge hundreds of dollars to program the new key in the event that they are unable to complete the task.
If you've lost your sole working key the dealer will replace your car's computer (known as the CIM or SAAB TWICE) in order to make a replacement, and will charge you the highest price for it. We can reprogram the existing EEPROM of your car's computer to make it ready for an additional key. This will save you more than 50% of the cost you spend at an auto dealer.
If you have owned a SAAB 9-3 a long time and you're aware of the ignition keys aren't very durable. If your ignition key isn't functioning properly, you must consider replacing it. They can become extremely sticky and the buttons are known to fall off. Fortunately, replacing the ignition key isn't as complicated as it seems and is fairly easy to do using the appropriate tools.